6506> (enable) show config This command shows non-default configurations only. Use 'show config all' to show both default and non-default config .........
................ ................
..............
..
begin ! # ***** NON-DEFAULT CONFIGURATION ***** ! ! #time: Thu Jan 4 2001, 08:27:22 ! #version 5.4(3) #软件版本 ! set passWord $2$lnsk$mgJ84scE.A51hPR0Zbdfv/ #加密后的telnet密码 set enablepass $2$RFAC$BDgIVKdk3gl1RD4.DaNcu. #加密后的enable密码 ! #system set system name 6506 #系统名称 ! #! #vtp set vtp domain _domain # VTP域名 set vtp passwd _password # VTP域密码 set vlan 1 name default type ethernet mtu 1500 said 100001 state #建立VLAN set vlan 2 name vlan2 type ethernet mtu 1500 said 100002 state act set vlan 3 name valn3 type ethernet mtu 1500 said 100003 state acti
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 st set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101 e stp ieee set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 p ibm set vlan 1003 name token-ring-default type trcrf mtu 1500 said 10 ve mode srb aremaxhop 7 stemaxhop 7 backupcrf off ! #ip set interface sc0 1 10.1.1.253/255.255.255.0 10.1.1.255 #本交换机的IP地址
set ip route 0.0.0.0/0.0.0.0 10.1.1.254 #默认网关 set ip alias default 0.0.0.0 #设置ip对应的设备名，方便治理 set ip alias 6506 10.1.1.253 #用途如：ping 2620, telnet 3548_2a set ip alias msfc 10.1.1.254 set ip alias 4912 10.1.1.252 set ip alias 2620 10.1.8.250 ... ! #set boot command set boot config-register 0x102 #启动寄存器值及启动文件 set boot system Flash bootflash:cat6000-sup.5-4-3.bin ! #mls set mls flow full #多层交换流类型 ! #security ACLs #访问列表 clear security acl all #server set security acl ip server deny ip host 10.1.1.199 host 10.1.1.200 # commit security acl all ! # default port status is enable ! ! #module 1 : 2-port 1000BaseX Supervisor #治理引擎（含2口千兆模块） ! #module 2 : 8-port 1000BaseX Ethernet #8口千兆交换模块 set vlan 5 2/1 #指定端口2/1到vlan 5 set port name 2/1 gg #设置端口名称 set port name 2/2 cb set port name 2/3 server1 set port name 2/4 server2 set port name 2/5 3548_2a set udld enable 2/6-8 #未安装GBIC时激活检测 set trunk 2/1 off dot1q 1-1005 #设置2/1为运行802.1Q协议的干道，答应vlan 1-1005通过 set trunk 2/2 on dot1q 1-1005 set trunk 2/3 on dot1q 1-1005 set trunk 2/4 on dot1q 1-1005 set trunk 2/5 nonegotiate isl 1-1005 ! #module 3 : 8-port 1000BaseX Ethernet #8口千兆交换模块 set port name 3/4 3524_17a set port name 3/5 3548_9b set port name 3/6 3548_9a set port name 3/7 3548_f4a set port name 3/8 3548_12a set udld enable 3/1-3 set trunk 3/1 on dot1q 1-1005 set trunk 3/4 nonegotiate isl 1-1005 #设置3/4为运行isl协议的干道，答应vlan 1-1005通过 set trunk 3/5 nonegotiate isl 1-1005 set trunk 3/6 nonegotiate isl 1-1005 set trunk 3/7 nonegotiate isl 1-1005 set trunk 3/8 nonegotiate isl 1-1005 ! #module 4 empty ! #module 5 empty ! #module 6 empty ! #module 15 : 1-port Multilayer Switch Feature Card set port name 15/1 msfc #路由、多层交换模块 ! #module 16 empty end
