mfr-2# show version Cisco Internetwork Operating System Software IOS (tm) GS Software (GSR-P-M), Version 11.2(15)GS1a, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Mon 28-Dec-98 14:39 by tamb Image text-base: 0x60010900, data-base: 0x606C4000 ROM: System Bootstrap, Version 11.2(9)GS5, [tamb 176] EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) mfr_2 uptime is 4 minutes System returned to ROM by reload System image file is "slot0:gsr-p-mz.112-15.GS1a", booted via slot0: cisco 12008/GRP (R5000) PRocessor (revision 0x01) with 262144K bytes of memory. R5000 processor, Implementation 35, Revision 2.1 (512KB Level 2 Cache) Last reset from power-on 1 Clock Scheduler Card(s) 1 Quad-port OC3c ATM controller (4 ATM). 1 Single-port OC12c ATM controller (1 ATM). 1 four-port OC3 POS controller (4 POS). 1 Ethernet/IEEE 802.3 interface(s) 5 ATM network interface(s) 4 Packet over SONET network interface(s) 507K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x102
WARNING: Old Rom Monitor in slot 0 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 0 Use "upgrade fabric-downloader" command to update the image WARNING: Old Rom Monitor in slot 1 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 1 Use "upgrade fabric-downloader" command to update the image WARNING: Old Rom Monitor in slot 2 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 2 Use "upgrade fabric-downloader" command to update the image
从以上警告消息 ，我们能发现我们需要升级ROM监控器和矩阵下载程序。
使用 show diag 命令确定什么线路卡您升级和其当前状态。 注重线路卡在一 个答应状态(IOS RUN)，如显示在下面的 show diag命令输出。当 线路卡在一个答应状态时，您能升级固件。
mfr_2#show diag 0 SLOT 0 (RP/LC 0 ): 4 Port Packet Over SONET OC-3c/STM-1 Multi Mode MAIN: type 33, 800-2396-02 rev A0 dev 16777215 HW config: 0x01 SW key: FF-FF-FF PCA: 73-2147-05 rev A0 ver 4 HW version 1.1 S/N CAB02040049 MBUS: MBUS Agent (1) 73-2146-06 rev A0 dev 0 HW version 1.1 S/N CAB014600ME Test hist: 0xFF RMA#: FF-FF-FF RMA hist: 0xFF DIAG: Test count: 0xFFFFFFFF Test results: 0xFFFFFFFF MBUS Agent Software version 01.35 (RAM) (ROM version is 01.33) Using CAN Bus A ROM Monitor version 0E.00 Fabric Downloader version used 00.13 (ROM version is 11.03) Board is analyzed Board State is Line Card Enabled (IOS RUN ) Insertion time: 00:00:11 (00:04:16 ago) DRAM size: 268435456 bytes FrFab SDRAM size: 67108864 bytes ToFab SDRAM size: 67108864 bytes
下一个步骤将升级线路卡。执行此，使用 upgrade命令。 下面是 upgrade命令选项 列表。
mfr_2#upgrade ? all all GSR rom images fabric-downloader fabric downloader mbus-agent-rom mbus agent rom post Power On Self Test rom-monitor rom monitor
由于有一个ROM监控器警告在 show version命令输出，您 在卡需要升级ROM监控器。upgrade命令在句法示例显示如下 ： mfr_2#upgrade rom-monitor ? all all slots slot slot number <cr> mfr_2#upgrade rom-monitor slot ? <0-7> slot number mfr_2#upgrade rom-monitor slot 0 ========= Line Card (Slot 0) ======= EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv mfr_2# SLOT 0:Upgraded linecard ROM monitor sUCcessfully
mfr_2#upgrade all ? all all slots slot slot number <cr> mfr_2#upgrade all all This will take around 7-10 minutes for a full chassis Ensure that GSR is not power cycled during the upgrade Premature termination of this command may render the GSR inoperable Please consult the documentation for more information Continue ? [no]: yes Starting upgrade, please wait Upgrading line card rom ========= Line Card (Slot 0) ======= EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 1) ======= SLOT 0:Upgraded linecard ROM monitor successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 2) ======= SLOT 1:Upgraded linecard ROM monitor successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv Upgrading line card floader ========= Line Card (Slot 0) ======= SLOT 2:Upgraded linecard ROM monitor successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 1) ======= SLOT 0:Upgraded linecard fabric loader successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv ========= Line Card (Slot 2) ======= SLOT 1:Upgraded linecard fabric loader successfully EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEppppppppppppppppppvvvvvvvvvvvvvvvvvv SLOT 2:Upgraded linecard fabric loader successfully Upgrading the MBUS agent rom on slot 0 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 1 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 2 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 17 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 24 rom programmed successfully with 255 retries Upgrading the MBUS agent rom on slot 7 rom programmed successfully with 255 retries Upgrading grp rom in slot 7 The current revision of GRP ROM is: 175 The new revision of GRP ROM will be: 175 NOTE: 1) GRP ROM upgrade typically takes 30 to 240 seconds. 2) After GRP ROM upgrade the GRP will be reset. Continue GRP ROM upgrade? [yes/no]: n
mfr_2#show version Cisco Internetwork Operating System Software IOS (tm) GS Software (GSR-P-M), Version 11.2(15)GS1a, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Mon 28-Dec-98 14:39 by tamb Image text-base: 0x60010900, data-base: 0x606C4000 ROM: System Bootstrap, Version 11.2(9)GS5, [tamb 176] EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) mfr_2 uptime is 7 minutes System returned to ROM by reload System image file is "slot0:gsr-p-mz.112-15.GS1a", booted via slot0: cisco 12008/GRP (R5000) processor (revision 0x01) with 262144K bytes of memory. R5000 processor, Implementation 35, Revision 2.1 (512KB Level 2 Cache) Last reset from power-on 1 Clock Scheduler Card(s) 1 Quad-port OC3c ATM controller (4 ATM). 1 Single-port OC12c ATM controller (1 ATM). 1 four-port OC3 POS controller (4 POS). 1 Ethernet/IEEE 802.3 interface(s) 5 ATM network interface(s) 4 Packet over SONET network interface(s) 507K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x102
WARNING: Old Rom Monitor in slot 0 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 0 Use "upgrade fabric-downloader" command to update the image WARNING: Old Rom Monitor in slot 1 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 1 Use "upgrade fabric-downloader" command to update the image WARNING: Old Rom Monitor in slot 2 Use "upgrade rom-monitor" command to update the image WARNING: Old Fabric Downloader in slot 2 Use "upgrade fabric-downloader" command to update the image
mfr_2# configure terminal Enter configuration commands, one per line. End with CNTL/Z. mfr_2(config)#microcode reload mfr_2(config)#^Z !-- This represents the CNTL + Z key combination.
您能再现在发出 show version命令。表明下面的输出不包含警告消息升级是成功的。
mfr_2#show version Cisco Internetwork Operating System Software IOS (tm) GS Software (GSR-P-M), Version 11.2(15)GS1a, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Mon 28-Dec-98 14:39 by tamb Image text-base: 0x60010900, data-base: 0x606C4000 ROM: System Bootstrap, Version 11.2(9)GS5, [tamb 176] EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) mfr_2 uptime is 7 minutes System returned to ROM by reload System image file is "slot0:gsr-p-mz.112-15.GS1a", booted via slot0: 12008/GRP (R5000) processor (revision 0x01) with 262144K bytes of memory. R5000 processor, Implementation 35, Revision 2.1 (512KB Level 2 Cache) Last reset from power-on 1 Clock Scheduler Card(s) 1 Quad-port OC3c ATM controller (4 ATM). 1 Single-port OC12c ATM controller (1 ATM). 1 four-port OC3 POS controller (4 POS). 1 Ethernet/IEEE 802.3 interface(s) 5 ATM network interface(s) 4 Packet over SONET network interface(s) 507K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x102 mfr_2#
mfr_2#configure terminal Enter configuration commands, one per line. End with CNTL/Z. mfr_2(config)#miv mfr_2(config)#mic mfr_2(config)#microcode ? GE-1 1 Port Gigabit Ethernet OC12-4-POS-ED 4 Port E.D. Packet Over SONET OC-12c/STM-4 OC12-ATM 1 port ATM Over SONET OC12c/STM-4c OC12-CH-DS3 1 port SONET OC12 channelized to DS3 OC12-CH-STS3 1 port SONET OC12 channelized to STS-3c/STM-1 OC12-POS 1 Port Packet Over SONET OC-12c/STM-4c OC3-POS-4 4 Port Packet Over SONET OC-3c/STM-1 OC48-POS-ED 1 Port E.D. Packet Over SONET OC-48c/STM-16 reload force reloading of microcode mfr_2(config)#microcode reload mfr_2(config)#microcode reload ? <0-7> Slot number of card to reload <cr>
非凡注重事项 在升级之前，假如线路卡不过来，输入以下命令： gsr# configure terminal gsr(config)# service download-fl gsr(config)# microcode reload gsr(config)# ^Z <-- This represents the CNTL + Z key combination.
