贴一个单臂路由的配置实例 交换机配置 3512xl#show running-config Building configuration...
Current configuration:
! version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service passWord-encryption ! hostname 3512xl ! no logging console enable password mysecret ! ! ! ! ! ip subnet-zero ! ! ! interface FastEthernet0/1 switchport mode trunk !
!-- If 802.1Q is configured, !-- you will instead see the following output !-- under interface FastEthernet0/1: !-- interface FastEthernet0/1 !-- switchport trunk encapsulation dot1q !-- switchport mode trunk
! interface FastEthernet0/2 switchport access vlan 2 spanning-tree portfast ! interface FastEthernet0/3 spanning-tree portfast ! interface FastEthernet0/4 ! interface FastEthernet0/5 ! interface FastEthernet0/6 ! interface FastEthernet0/7 ! interface FastEthernet0/8 ! interface FastEthernet0/9 ! interface FastEthernet0/10 ! interface FastEthernet0/11 ! interface FastEthernet0/12 ! interface GigabitEthernet0/1 ! interface GigabitEthernet0/2 ! interface VLAN1 ip address 10.10.10.2 255.255.255.0 no ip directed-broadcast no ip route-cache ! ip default-gateway 10.10.10.1 ! line con 0 transport input none stopbits 1 line vty 0 4 password mysecret login line vty 5 15 login ! end
路由器配置
Current configuration: ! version 12.1 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname c2600 ! no logging console enable password mysecret ! ! ! ! ! ip subnet-zero ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/0.1 encapsulation isl 1 ip address 10.10.10.1 255.255.255.0 no ip redirects !
!-- If 802.1Q is configured, !-- you will instead see the following output !-- under interface FastEthernet0/0.1: !-- interface FastEthernet0/0.1 !-- encapsulation dot1Q 1 native !-- ip address 10.10.10.1 255.255.255.0
! ! interface FastEthernet0/0.2 encapsulation isl 2 ip address 10.10.11.1 255.255.255.0 no ip redirects !
!-- If 802.1Q is configured, !-- you will instead see the following output !-- under interface FastEthernet0/0.2: !-- interface FastEthernet0/0.2 !-- encapsulation dot1Q 2 !-- ip address 10.10.11.1 255.255.255.0
! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! ip classless no ip http server ! ! ! line con 0 transport input none line aux 0 line vty 0 4 password mysecret login ! no scheduler allocate end
PPPoE配置实例（2600路由器接ADSL Modem）
[[The No.2 Picture.]]
hostname pooh ip host rund 172.17.247.195 ! ip subnet-zero no ip domain-lookup ! vpdn enable no vpdn logging ! vpdn-group 1 request-dialin PRotocol pppoe ! ! ! ! interface Ethernet0/0 ip address 10.200.56.22 255.255.255.0 ip nat inside no ip mroute-cache ! ! ! ! interface Ethernet0/1 no ip address pppoe enable pppoe-client dial-pool-number 1 ! interface Dialer1 ip address negotiated ip nat outside ip mtu 1492 encapsulation ppp no ip mroute-cache dialer pool 1 dialer-group 1 ppp authentication pap ppp pap sent-username cisco password cisco1 ! ip classless no ip http server ! dialer-list 1 protocol ip permit ip nat inside source list 1 interface Dialer1 overload ip route 0.0.0.0 0.0.0.0 dialer1 access-list 1 permit 10.200.56.0 0.0.0.255 ! line con 0 exec-timeout 0 0 transport input none line vty 0 4 login password ww ! end
PPPoA配置实例 （2600路由器连接Wic-1ADSL）
vpdn enable no vpdn logging
!--- default.
! vpdn-group pppoe request-dialin
!--- we are the PPPoE client requesting to establish !--- a session with the aggregation unit (6400 NRP).
protocol pppoe !
!--- internal Ethernet network.
! interface FastEthernet0 ip address 10.92.1.182 255.255.255.0 ip nat inside
!--- DSL interface.
! interface ATM0 no ip address no atm ilmi-keepalive bundle-enable dsl Operating-mode auto hold-queue 224 in
!--- All defaults.
!--- PPPoE runs on top of AAL5SNAP, but the !--- encap aal5snap command is not used.
ppp authentication chap callin ppp chap hostname ppp chap password !
!--- The ISP will instrUCt you regarding !--- the type of authentication to use. !--- To change from PPP CHAP to PPP PAP, !--- replace the following three lines: !--- ppp authentication chap callin !--- ppp chap hostname !--- ppp chap password !--- with the following two lines: !--- ppp authentication pap callin !--- ppp pap sent-username password
!--- For NAT we are going to overload on the Dialer1 !--- interface and add a default route out !--- since dialer ip address can change.
ip nat inside source list 1 interface Dialer1 overload ip classless ip route 0.0.0.0 0.0.0.0 dialer1 no ip http server ! access-list 1 permit 10.92.1.0 0.0.0.255
