Router# show controllers e1 e1 0/0 is up. Applique type is Channelized E1 - unbalanced Framing is CRC4, Line Code is HDB3 No alarms detected. Data in current interval (725 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 24 hours) 0 Line Code Violations, 0 Path Code Violations, 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
以下例子为E1连接3条64K专线, 帧类型为NO-CRC4,非平衡链路,路由器具体设置如下: shanxi#wri t Building configuration...
Current configuration: ! version 11.2 no service udp-small-servers no service tcp-small-servers ! hostname shanxi ! enable secret 5 $1$XN08$Ttr8nfLoP9.2RgZhcBzkk/ enable passWord shanxi ! ! ip subnet-zero ! controller E1 0 framing NO-CRC4 channel-group 0 timeslots 1 channel-group 1 timeslots 2 channel-group 2 timeslots 3 ! interface Ethernet0 ip address 133.118.40.1 255.255.0.0 media-type 10BaseT ! interface Ethernet1 no ip address shutdown ! interface Serial0:0 ip address 202.119.96.1 255.255.255.252 no ip mroute-cache ! interface Serial0:1 ip address 202.119.96.5 255.255.255.252 no ip mroute-cache ! interface Serial0:2 ip address 202.119.96.9 255.255.255.252 no ip mroute-cache ! no ip classless ip route 133.210.40.0 255.255.255.0 Serial0:0 ip route 133.210.41.0 255.255.255.0 Serial0:1 ip route 133.210.42.0 255.255.255.0 Serial0:2 ! line con 0 line aux 0 line vty 0 4 password shanxi login ! end
二、PPP
PPP(Point-to-Point Protocol)是SLIP(Serial Line IP protocol)的继续者，它提供了跨过同步和异步电路实现路由器到路由器(router-to-router)和主机到网络(host-to-network)的连接。
CHAP(Challenge Handshake Authentication Protocol)和PAP(Password Authentication Protocol) (PAP)通常被用于在PPP封装的串行线路上提供安全性认证。使用CHAP和PAP认证,每个路由器通过名字来识别，可以防止未经授权的访问。 CHAP和PAP在RFC 1334上有具体的说明。 1. 有关命令 端口设置 任务 命令 设置PPP封装 encapsulation ppp1 设置认证方法 ppp authentication {chap chap pap pap chap pap} [if-needed] [list-name default] [callin] 指定口令 username name password secret 设置DCE端线路速度 clockrate speed 注：1、要使用CHAP/PAP必须使用PPP封装。在与非Cisco路由器连接时，一般采用PPP封装，其它厂家路由器一般不支持Cisco的HDLC封装协议。 2. 举例 路由器Router1和Router2的S0口均封装PPP协议，采用CHAP做认证，在Router1中应建立一个用户，以对端路由器主机名作为用户名，即用户名应为router2。同时在Router2中应建立一个用户，以对端路由器主机名作为用户名，即用户名应为router1。所建的这两用户的password必须相同。 设置如下： Router1: hostname router1 username router2 password xxx interface Serial0 ip address 192.200.10.1 255.255.255.0 clockrate 1000000 ppp authentication chap ! Router2: hostname router2 username router1 password xxx interface Serial0 ip address 192.200.10.2 255.255.255.0 ppp authentication chap !
相关调试命令： clear x25-vc show interfaces serial show x25 map show x25 route show x25 vc 3.2. 在以下实例中路由器router1和router2均通过svc与router连接，但router1和router2不通过svc直接连接，此三个路由器的串口运行RIP路由协议，使用了子接口的概念。 由于使用子接口，router1和router2均学习到了访问对方局域网的路径，若不使用子接口，router1和router2将学不到到对方局域网的路由。
interface serial 0.1 point-to-point ip address 172.16.1.1 255.255.255.0 frame-reply interface-dlci 105 ! interface serial 0.2 point-to-point ip address 172.16.2.1 255.255.255.0 frame-reply interface-dlci 102 ! interface serial 0.3 point-to-point ip address 172.16.4.1 255.255.255.0 frame-reply interface-dlci 104 ! Router2: interface serial 0 encapsulation frame-relay ! interface serial 0.1 point-to-point ip address 172.16.2.2 255.255.255.0 frame-reply interface-dlci 201 ! interface serial 0.2 point-to-point ip address 172.16.3.1 255.255.255.0 frame-reply interface-dlci 203 ! 相关调试命令： show frame-relay lmi show frame-relay map show frame-relay pvc show frame-relay route show interfaces serial go top
4. 帧中继 Multipoint 配置实例: Router1: interface serial 0 encapsulation frame-reply ! interface serial 0.1 multipoint ip address 172.16.1.2 255.255.255.0 frame-reply map ip 172.16.1.1 201 broadcast frame-reply map ip 172.16.1.3 301 broadcast frame-reply map ip 172.16.1.4 401 broadcast ! Router2: interface serial 0 encapsulation frame-reply ! interface serial 0.1 multipoint ip address 172.16.1.1 255.255.255.0 frame-reply map ip 172.16.1.2 102 broadcast frame-reply map ip 172.16.1.3 102 broadcast frame-reply map ip 172.16.1.4 102 broadcast !
