第1段:启动IPX路由并配置IPX网络 R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#ipx routing? H.H.H IPX address of this router
R1(config)#ipx routing R1(config)#int eO R1(config-if)#ipx netw 12 R1(config-if)#no sh R1(config-if)#^Z R1# Term_Server#2 [Resuming connection 2 to R2 ...]
R2#conft Enter configuration commands, one per line. End with CNTL/Z. R2(config)#ipx routing R2(config)#int eO R2(config-if)#ipx netw 12 R2(config-if)#no sh R2(config-if)#^Z R2# 第2段:查看IPX协议信息并测试连通性 R1#sh ipx int eO Ethemet0 is up, line PRotocol is up IPX address is 12.0000.0c76,NOVELL-ETHER[up] Delay of this IPX network, in ticks is I throughput 0 link delay 0 IPXWAN processing not enabled on this interface. IPX SAP update interval is 60 seconds IPX type 20 propagation packet forwarding is disabled Incoming access list is not set Outgoing access list is not set IPX helper access list is not set SAP GGS output filter list is not set SAP GNS processing enabled, delay 0 ms, output filter list is not set SAP Input filter list is not set SAP Output filter list is not set SAP Router filter list is not set Input filter list is not set Output filter list is not set Router filter list is not set Netbios Input host access list is not set Netbios Input bytes access list is not set Netbios Output host access list is not set Netbios Output bytes access list is not set Updates each 60 seconds aging multiples RIP: 3 SAP: 3 SAP interpacket delay is 55 ms, maximum size is 480 bytes RIP interpacket delay is 55 ms, maximum size is 432 bytes RIP response delay is not set IPX accounting is disabled IPX fast switching is configured (enabled) RIP packets received 0, RIP packets sent 1, 0 Throttled RIP specific requests received 0, RIP specific replies sent 0 RIP general requests received 0, 0 ignored, RIP general replies sent 0 SAP packets received 0, SAP packets sent 1, 0 Throttled SAP GNS packets received 0, SAP GNS replies sent 0 SAP GGS packets received 0, 0 ignored, SAP GGS replies sent 0 R1#ping ipx 12.0000.0c76ef736
Type escape sequence to abort. Sending 5, 100-byte IPX Novell Echoes to 12.0000.0c76.f736, timeout is 2 seconds: !!!!! SUCcess rate is 100 perceiit(5/5),round-trip min/avg/max=4/5/8 ms R1# Term_Server#2 [Resuming connection 2 to R2 ...] R2#ping ipx 12.0000.0c76.f736
Type escape sequence to abort. Sending 5, 100-byte IPX Novell Echoes to 12.0000.0c76.f736, timeout is 2 seconds: !!!!! Success rate is 100 percent(5/5),round-trip min/avg/max=4/5/8 ms
监测清单9-1配置IPX协议在以太网上的封装类型 R2#conft Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int eO R2(config-if)#ipx network 12 ? encapsulation IPX encapsulation R2(config-if)#ipx network 12 encap ? arpa IPX Ethernet_II hdlc HDLC on serial links novell-ether IPX Ethernet-802.3 novell-fddi IPX FDDI RAW sap IEEE 802.2 on Ethernet,FDDI,Token Ring snap IEEE 802.2 SNAP on Ethernet,Token Ring,and FDDI
R2(config-if)#ipx network 12 encap sap R2(config-if)# R2#ping ipx 12.0000.0c76.f736 Type escape sequence to abort. Sending 5, 100-byte IPX Novell Echoes to 12.0000.0c76.f736, timeout is 2 seconds ..... Success rate is 0 percent(0/5)
R2#conft Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int e0 R2(config-if)#ipx netw 12 encap novell-ether R2(config-if)#ipx netw 12a encap arpa secon R2(config-if)#ipx netw 12b encap sap secon R2(config-if)#ipx netw 12c encap snap secon R2(config-if)#^Z Term_Server#1 [Resuming connection 2 to R1 ... ]
R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#int eO R1(config-if)#ipx netw 12 encap novell-ether R1(config-if)#ipx netw 12a encap arpa secondary R1(config-if)#ipx netw 12b encap sap secon R1(config-if)#ipx netw 12c encap snap secon R1(config-if)#^Z R1# R1#ping ipx 12.0000.0c8e.cdd2
Type escape sequence to abort. Sending 5,100-byte IPX Novell Echoes to 12.0000.0c8e.cdd2,timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms R1#ping ipx 12a.0000.0c8e.cdd2
Type escape sequence to abort. Sending 5, 100-byte IPX Novell Echoes to 12A.OOOO.Oc8e.cdd2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max=4/5/8 ms R1#ping ipx 12b.OOOO.Oc8e.cdd2
Type escape sequence to abort. Sending 5, 100-byte IPX Novell Echoes to 12B.OOOO.Oc8e.cdd2, timeout is 2 seconds: !!!!! Success rate is 100
