1、 初始化交换机
Cisco9148 SAN交换机首次配置时，需要先做初始化设置，设置完成后才可以登录图形化界面。
使用随机自带的串口调试线缆进行连接，进行如下配置。
Enter the password for "admin":
Confirm the password for "admin":
---- Basic System Configuration Dialog ----
This setup utility will guide you through the basic configuration of
the system. Setup configures only enough connectivity for management
of the system.
Please register Cisco MDS 9000 Family devices promptly with your
supplier. Failure to register may affect response times for initial
service calls. MDS devices must be registered to receive entitled
support services.
Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
to skip the remaining dialogs.
Would you like to enter the basic configuration dialog (yes/no): y
Create another login account (yes/no) [n]: <Enter>
Configure read-only SNMP community string (yes/no) [n]: <Enter>
Configure read-write SNMP community string (yes/no) [n]: <Enter>
Enter the switch name : localhost
Continue with Out-of-band (mgmt0) management configuration? (yes/no) [y]: <Enter>
Mgmt0 IPv4 address : 10.77.77.77
Mgmt0 IPv4 netmask : 255.255.255.0
Configure the default gateway? (yes/no) [y]: n
Configure advanced IP options? (yes/no) [n]: <Enter>
Enable the ssh service? (yes/no) [y]: n
Enable the telnet service? (yes/no) [n]: y
Enable the http-server? (yes/no) [y]: <Enter>
Configure clock? (yes/no) [n]: <Enter>
Configure timezone? (yes/no) [n]: <Enter>
Configure summertime? (yes/no) [n]: <Enter>
Configure the ntp server? (yes/no) [n]: <Enter>
Configure default switchport interface state (shut/noshut) [shut]: <Enter>
Configure default switchport trunk mode (on/off/auto) [on]: auto
Configure default switchport port mode F (yes/no) [n]: <Enter>
Configure default zone policy (permit/deny) [deny]: <Enter>
Enable full zoneset distribution? (yes/no) [n]: <Enter>
Configure default zone mode (basic/enhanced) [basic]: <Enter>
The following configuration will be applied:
password strength-check
switchname localhost
interface mgmt0
ip address 10.77.77.77 255.255.255.0
no shutdown
no feature ssh
feature telnet
feature http-server
system default switchport shutdown
system default switchport trunk mode auto
no system default zone default-zone permit
no system default zone distribute full
no system default zone mode enhanced
Would you like to edit the configuration? (yes/no) [n]: <Enter>
Use this configuration and save it? (yes/no) [y]: <Enter>
[########################################] 100%
到此，设备初始化完成。
2、打开IE浏览器，在地址栏输入配置好的IP地址（http://10.77.77.77），打开如下界面。
3、点击上图中的“Cisco Device Manager”打开如下界面。
4、点击上图中的“Continue”，打开如下界面。
5、点击上图中的“Next”，进行软件的安装。
点击“下一步”
点击“Install”
点击“是”，开始安装软件。
6、软件安装完成后，打开如下界面，在密码栏输入设置好的密码“123ibm!@#IBM”。
7、点击“Open”，打开控制界面。
8、点击“FC->Quick Config”，打开配置界面。
9、在打开的控制界面中，进行zone的设置。
点击“Next”，查看zone的设置是否正确。
点击“Finish”，完成zone的配置。
10、在命令行中，运行如下命令，查看zone是否激活。
admin# show zone active
zone name Z_FC1_5_FC1_1_V1 vsan 1
* fcid 0xb80500 [interface fc1/5 swwn 20:00:00:05:73:da:b1:50]
* fcid 0xb80000 [interface fc1/1 swwn 20:00:00:05:73:da:b1:50]
zone name Z_FC1_5_FC1_2_V1 vsan 1
* fcid 0xb80500 [interface fc1/5 swwn 20:00:00:05:73:da:b1:50]
* fcid 0xb80200 [interface fc1/2 swwn 20:00:00:05:73:da:b1:50]
zone name Z_FC1_6_FC1_3_V1 vsan 1
* fcid 0xb80400 [interface fc1/6 swwn 20:00:00:05:73:da:b1:50]
* fcid 0xb80100 [interface fc1/3 swwn 20:00:00:05:73:da:b1:50]
zone name Z_FC1_6_FC1_4_V1 vsan 1
* fcid 0xb80400 [interface fc1/6 swwn 20:00:00:05:73:da:b1:50]
* fcid 0xb80300 [interface fc1/4 swwn 20:00:00:05:73:da:b1:50]
zone name $default_zone$ vsan 1
11、运行如下命令，查看zoneset是否已保存成功。
admin# show zoneset
zoneset name ZONESET_V1 vsan 1
zone name Z_FC1_5_FC1_1_V1 vsan 1
interface fc1/5 swwn 20:00:00:05:73:da:b1:50
interface fc1/1 swwn 20:00:00:05:73:da:b1:50
zone name Z_FC1_5_FC1_2_V1 vsan 1
interface fc1/5 swwn 20:00:00:05:73:da:b1:50
interface fc1/2 swwn 20:00:00:05:73:da:b1:50
zone name Z_FC1_6_FC1_3_V1 vsan 1
interface fc1/6 swwn 20:00:00:05:73:da:b1:50
interface fc1/3 swwn 20:00:00:05:73:da:b1:50
zone name Z_FC1_6_FC1_4_V1 vsan 1
interface fc1/6 swwn 20:00:00:05:73:da:b1:50
interface fc1/4 swwn 20:00:00:05:73:da:b1:50
12、两台交换机中的WWN号。
